產品簡介
I. Product Introduction
SBT-207A/B/C/M為常溫沉薄銅溶液，控制維護方便，消耗量少。
SBT-207A/B/C/M is a kind of thin electro-less plating copper solution under normal temperature, which is convenient to maintain, with less consumption.
裝置
II. Device
載體/工具
Carrier/Tool |
材質要求
Material Requirements |
槽
Tank |
聚氯乙烯、聚丙烯、聚四氟乙烯
Polyethylene, polypropylene, teflon |
鼓氣裝置
Blow device |
需要
Required |
過濾泵
Filter pump |
5-10微米過濾能力的聚丙烯濾芯
Polypropylene filer element with filter capacity of 5-10 μm |
三、100升工作液配制
III. Preparation of 100 liters’ working solution
名稱
Product Name |
數量
Quantity |
軟化水
Softened water |
80L |
| SBT-207M |
7-9L |
| SBT-207A |
5-7L |
| SBT-207B |
5-7L |
| SBT-207C |
1.3-1.7L |
四、工藝條件
IV.Technical Conditions
組份/參數
Component/Parameter |
最佳值/工作范圍/要求
Optimal value /work scope/requirement |
工作溫度
Working temperature |
25-35℃ |
處理時間
Processing time |
15分鐘
15min |
攪拌方式
Mixing means |
連 連續空氣鼓泡
Continuous air bubling |
循環過濾
Circulation and filtration |
可連續進行或間隔進行
Continuous or intermittent |
五、槽液維護（以100升槽計）
V. Maintenance of Solution (Calculated with 100L tank)
1、成份指標
1. Component index
成分
Component |
工作范圍
Working scope |
最佳值
Optimal value |
銅（克/升）
Cu (k/l) |
1.5-2.0 |
1.8 |
氫氧化鈉（克/升）
NaOH (k/l) |
10-14 |
12 |
甲醛（克/升）
Methanal (k/l) |
4-9 |
6 |
2、工作液處理100ft2板，需補加SBT-207A 1.2L，SBT-207B 1.2L。
2. 1.2L SBT-207A and 1.2L SBT-207B shall be added each time when 100 ft2 plate is processed with the working solution.
3、當室溫低于25℃時可每天適量補加甲醛100-200ml，也可根據分析結果補加。
3. When the ambient temperature is lower than 25℃, 100-200ml methanal shall be added every day, or add appropriate amount of methanal according to the results of analysis.
4、存放需保持空氣鼓氣。
4. Keep air blowing for storage.
5、長期停工前需用稀硫酸將工作液PH值降至8-10。
5. Before long-term shut down, the PH of working solution shall be lowered to 8-10 with dilute sulphuric acid.
6、當鍍液密度達至1.10克/立方厘米，必須放掉一半工作液，并配制新溶液。
6. When the density of the plating solution reaches 1.10g/cm3, half of the working solution shall be drained out, and new solution shall be prepared.
六、分析方法
VI. Analysis Methods
(一) Cu(銅)
(I) Cu
1. 步驟
1. Steps
(1). 取25mL Sample，加40mL(20%)H2SO4
(1) Take 25mL Sample, add 40mL(20%)H2SO4
(2). 加0.5g氨基磺酸加熱煮沸1min,冷卻 5 分鐘
(2) Add 0.5g sulfamic acid and heat the solution to boiling, keep it boiling for 1min, and cool down for 5min.
(3). 加2g KI攪拌3分鐘
(3) Add 2g KI, mix for 3 min.
(4). 以0.1N Na2S2O3 滴定至淡黃色
(4) Titrate the solution to light yellow with 0.1N Na2S2O3
(5). 加5mL淀粉(Starch)指示劑
(5) Add 5mL Starch indicator
(6). 加20mL 10% KSCN
(6) Add 20mL of 10% KSCN
(7). 繼續以0.1N Na2S2O3 滴定至乳白色
(7) Continue to titrate the solution to ivory with 0.1N Na2S2O3
2. 計算
2. Calculation
Cu(g/L) = N of Na2S2O3×mLs of Na2S2O3×63.54÷25
例 eg. : 2.9g/L = 0.1N×11.4mL×63.54÷25
3. 分析補加公式
3. Adding formula analysis
補加物料207A/B(L):(標準值—分析值)×槽積/ 29
Added material 207A/B(L): (standard value-analysis value) ×volume of the tank/29
(二) NaOH&HCHO分析法
(II) NaOH&HCHO analysis method
步驟
1. Steps
Note : 1M Na2SO3須先利用0.1N NaOH 調至pH=10
Note : The PH of 1M Na2SO3 shall be adjusted to 10 with 0.1N NaOH
(1). 取5mL Sample于燒杯中加100L去離子水
(1) Take 5mL Sample into a beaker, and add 100L deionized water
(2). 沖洗電極放入Sample
(2) Wash the electrode, and put them into the Sample
(3). 以0.1N HCl標準液滴定至 pH10.2 ---- A mLs (NaOH含量)
(3) Titrate the solution to pH10.2 ---- A mLs (NaOH content) with 0.1N HCl standard solution
(4). 繼續以0.1N HCl調至pH10
(4) Continue to titrate with 0.1N HCl until the PH is 10
(5). 加入25mL 1M Na2SO3,攪拌5min
(5) Add 25mL 1M Na2SO3, mix for 5min
(6). 以0.1N HCl標準液滴定至pH10 ---- B mLs (HCHO含量)
(6) Titrate the solution to pH10 ----B mLs (HCHO content) with 0.1N HCl standard solution
2. 計算
2. Calculation
(1) NaOH (g/L) = N of HCl×A mLs of HCl ×40÷5
例 eg : 12(g/L) = 0.1N×15mL×40÷5
分析補加公式:補加物料207B(L) :(標準值—分析值)×槽積/340
Adding formula analysis: Added material 207B(L): (standard value-analysis value) ×volume of the tank/340
(2) HCHO (g/L) = B mLs of HCl×N of HCl×30÷5
例 eg : 5(g/L) = 0.1N×8.3mL×30÷5
析補加公式: 補加物料207C(L) :(標準值—分析值)×槽積 /400 Adding formula analysis: Added material 207C(L): (standard value-analysis value) ×volume of the tank/400
七、廢水處理
VII. Wastwater Treatment
加入1%體積比的甲醛，15克/L的硫酸亞鐵，加熱到70℃直到溶液分解，使銅沉淀出來為止。
Add methanal with 1% volume ratio, 15g/L FeSO4, heat to 70℃, until the solution is pyrolyzed, and Cu deposites. |
